47mm - 70cc cylinder head for Piaggio liquid cooled engines, these are designed for the DMP 70cc cylinder kits but may be suitable for...

Oil pump for Yamaha Aerox/ Minarelli engines.

The standard oil pump mixes at maximum 2% or 50:1 ratio. Some performance cylinder kits are...

Replacement liquid cooled 50cc cylinder head for Yamaha Aerox/ Minarelli engine.

Water pump grommet for Aerox/ Minarelli engines.

*Sold singley*

Replacement camshaft unit for Chinese 125cc 4-Stroke scooter engines with 152QMI engines.

Standard, complete with bearings and camshaft...

Genuine Yamaha replacement water heater pipe for Yamaha Aerox/ Minarelli engines.

These are the little pipes which connect from the top of...

Replacement flywheel side crankcase half for Minarelli/ Yamaha Aerox Engines.

Cylinder head bolt, nut set available in M6 or M7 thread 13mm long.

Choose M6 thread for all Piaggio based 50cc moped engines.

Choose M7...

Set of 4 cylinder studs and nuts for Piaggio 50cc 2-stroke moped engines.

Cylinder stud, bolt and washer kit for Minarelli vertical engines.

This is a complete kit which includes four 106mm long studs and nuts/...

Yamaha Aerox centre engine mount bush/ shaft. This is the long tube which goes though the middle of your engine cases which the swing arm...

Exhaust stud, nut and gasket set - this is the perfect kit for mopeds and includes the 3 main items you will need when fitting a new...

Replacement genuine Yamaha Aerox swing arm bolt.

This is the bolt which passes through the 2 engine lugs through the long swingarm spacer ...

High quality steel M6 flanged bolt, available in a range of different lengths.

These bolts are used all over all scooters and mopeds from...

Replacement standard cylinder head from Motoforce.

Fits 50cc Minarelli (horizontal) air cooled bikes.Motoforce Part No. MF28.16605

Replacement Motoforce cylinder head for Yamaha vertical air cooled engines e.g. BWS and MBK BoosterMotoforce Part No. MF28.16805

Crankcase breather kit from Motoforce Racing.

Why do you need a crankcase breather? During the downward strokes of the piston inside the...

Motoforce replacement cylinder head for liquid cooled Aerox/ Minarelli mopeds. 
Can be used to replace the standard cylinder head and...

This Naraku sport camshaft for Piaggio 50cc 4-stroke engines, this camshaft offers more aggresive timing together with longer valve opening...

Oil dip stick with rubber O-ring seal for Chinese GY6 mopeds.

Fits both 50cc and 125cc scooters.

2-stroke oil pump assembly for pretty much all Chinese 2-stroke moped (1E40QMB) engines.

Also fits most common CPI and Keeway bikes.

Oil pump dowel for Yamaha Aerox/ Minarelli bikes. This is the pin which drives the plastic oil pump wheel on the crank.

Note: Sold...

Air cooled 50cc cylinder head for Peugeot horizontal engine mopeds, this is a DMP branded cylinder head which will fit most makes of 50cc...

Standard replacement cylinder head for Peugeot liquid cooled standard 50cc cylinder kits.

Engine cover for all 50cc Piaggio/ Gilera air cooled bikes (2 stroke)

Genuine Piaggio replacement fan for Piaggio/ Gilera air cooled bikes.

Genuine Piaggio replacement oil pump belt. Fits all Piaggio/ Gilera 50cc moped engines.

Genuine Piaggio original part.

Oil pump drive wheel for 50cc Piaggio moped engines

Replacement plastic thermostat cover kit for Piaggio Malossi L/C cylinder kits.

Polini plastic thermostat cover for Piaggio liquid cooled Polini cylinder kits. 

Water pipe which locates by the engine flywheel/ stator.

Fits Piaggio/ Gilera water-cooled engines

Replacement standard cylinder head for 50cc air cooled Piaggio engines.

Piaggio/ Gilera flywheel cover.
Another genuine Piaggio replacement part at a bargain price !

Piaggio/ Gilera oil dipstick. Standard genuine Piaggio replacement part.Piaggio Part No. 482500

The Stage6 subframe allows you to fit a carburettor pointing directly to the back of the bike (above the rear wheel) where normally the...

In order to comply with exhaust emissions when they were produced, some Peugeot horizontal engines were fitted with an air compressor which...

Standard replacement cylinder head for Piaggio liquid-cooled mopeds.

Fits original standard cylinders or standard OEM style 50cc...

Cylinder head water caps for Yamaha Aerox/ Minarelli Malossi cylinders.

Standard Aerox has 2 small pipes running from the cylinder head to...

47mm - liquid cooled 70cc cylinder head for Yamaha Aerox/ Minarelli liquid cooled engines, these are designed for the DMP 70cc cylinder...

Engine mount circlips for Yamaha Aerox/ Jog / Neos mopeds.

These are the circlips used to secure the main engine shaft swing bolt (see...

Genuine Yamaha Aerox oil tank. A straight replacement for the old standard part.

Inexpensive replacement oil pump from Motoforce with the same capacity as the original.

Comes with the pipes necessary for direct...

Waterpump bolt for Yamaha Aerox/ Minarelli engines.Screws into the flywheel to turn the waterpump wheel.

Sold individually

Nut M7x1mm for all studs on the cylinder head. Fits all Minarelli engines.

Oil pump circlip for Yamaha Aerox/ Minarelli engines.

This is the circlip which goes on the crankshaft either side of the plastic oil pump...

47mm air cooled 70cc cylinder head for Minarelli engines, these are designed for the DMP 70cc cylinder kits but may be suitable for others...